1 single-event hardened, single supply, quad operational amplifiers isl7124srh, ISL7124SEH the single-event radiation hardened isl7124srh, ISL7124SEH consist of four inde pendent, high gain, internally frequency compensated operational amplifiers, specifically designed to operate from a single power supply over a wide range of voltages. these devices are functionally equivalent to industry standard 124 types, offering improvements in supply current and power supply rejection ratio. constructed with intersil?s dielectrically isolated, radiation hardened silicon gate (rsg) bicmos process, these devices are immune to single event latc hup. additionally, the design has been hardened to prevent single event transients (sets) in excess of 1v for lets up to 36mev/mg/cm 2 . the isl7124srh, ISL7124SEH have been specifically designed and manufactured to provide highly reliable performance in harsh radiation environments. they are total dose hardened to 300krad( si) and offer guaranteed performance over the full -55c to +125c military temperature range. specifications for rad hard qml devices are controlled by the defense logistics agency land and maritime (dla). the smd numbers listed here must be used when ordering. detailed electrical specifications for these devices are contained in smd 5962-02542. a ?h ot-link? is provided on our website for downloading. pin configuration isl7124srh, ISL7124SEH (flatpack cdfp3-f14) top view features ? qml qualified per mil-prf-38535 requirements ? electrically screened to dla smd # 5962-02542 ? radiation environment - total dose . . . . . . . . . . . . . . . . . . . . . . . . . .300krad(si)(max) -latch-up immune - set threshold (delta vo<1v) . . . . . .36mev/mg/cm 2 (min) ? single supply voltage range (5v to 30v) ? input common mode voltage range includes ground ? input offset voltage . . . . . . . . . . . . . . . . . . . . . . +/-10mv(max) ? input offset current . . . . . . . . . . . . . . . . . . . . . +/-150na(max) ? input bias current . . . . . . . . . . . . . . . . . . . . . . . . . 400na(max) ? open loop voltage gain . . . . . . . . . . . . . . . . . . . 20v/mv(min) ? power supply rejection ratio . . . . . . . . . . . . . . . . .70db(min) ? common mode rejection ratio . . . . . . . . . . . . . . . .70db(min) ? esd (hbm). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3000v(min) applications ? single supply operation of op-amp circuits ? general analog signal processing 14 13 12 11 10 9 8 2 3 4 5 6 7 1 out 1 -in 1 +in 1 +v cc +in 2 -in 2 out 2 out 4 -in 4 +in 4 -v cc +in 3 -in 3 out 3 ordering information ordering number internal mkt. number part marking temp. range (c) package pkg. dwg. # 5962f0254201vxc isl7124srhvf q 5962f02 54201vxc -55 to 12 5 14 lead ceramic metal seal flatpack k14.a 5962f0254201qxc isl7124srhqf q 5962f02 54201qxc -55 to 12 5 14 lead ceramic metal seal flatpack k14.a 5962f0254202vxc ISL7124SEHvf q 5962f02 54202vxc -55 to 125 14 lead ceramic metal seal flatpack k14.a isl7124srhf/proto isl7124srhf/proto isl7 /proto 124srhf - 55 to 125 14 lead ceramic metal seal flatpack k14.a caution: these devices are sensitive to electrostatic discharge; follow proper ic handling procedures. 1-888-intersil or 1-888-468-3774 | copyright intersil americas inc. 2002, 2012. all rights reserved intersil (and design) is a trademark owned by intersil corporation or one of its subsidiaries. all other trademarks mentioned are the property of their respective owners. february 23, 2012 fn9090.1
isl7124srh, ISL7124SEH 2 intersil products are manufactured, assembled and tested utilizing iso9000 quality systems as noted in the quality certifications found at www.intersil.com/design/quality intersil products are sold by description only. intersil corporat ion reserves the right to make changes in circuit design, soft ware and/or specifications at any time without notice. accordingly, the reader is cautioned to verify that data sheets are current before placing orders. information furnished by intersil is believed to be accurate and reliable. however, no responsi bility is assumed by intersil or its subsid iaries for its use; nor for any infringem ents of patents or other rights of third parties which may result from its use. no license is granted by implication or otherwise under any patent or patent rights of i ntersil or its subsidiaries. for information regarding intersil corporation and its products, see www.intersil.com fn9090.1 february 23, 2012 for additional products, see www.intersil.com/product_tree die characteristics die dimensions: 2640 m x 5020 m (104 mils x 198mils) thickness: 483 m 25.4 m (19 mils 1 mil) interface materials: glassivation: type: psg (phosphorous silicon glass) thickness: 8.0k? 1.0k? top metallization: type: alsicu thickness: 16.0k? 2k? substrate: radiation hardened silicon gate dielectrically isolated backside finish: silicon assembly related information: substrate potential: unbiased (di) additional information: worst case current density: <2.0 x 10 5 a/cm 2 transistor count: 276 metallization mask layout isl7124srh, ISL7124SEH layout not yet available. out 1 out 2 out 3 out 4 +in 1 -in 1 +v cc -v cc +in 2 +in 3 -in 3 +in 4 -in 4 -in 2
|
